How To Make Wood Filler For Guitar Repair

Learning how to inlay wood with a router is the best fashion to add some fashion to your woodworking project.

If you desire to utilize well-executed inlays to bring out the beauty of your piece, an inlay kit can play a major and helpful role in making that chore easier.

Despite the fact that you can make inlays with a fixed-base router, it's a bit hard to do so because of the tilting required.

That's why tight-fighting inlays are all-time executed with a plunge-base router.

How to Inlay Wood with a Router

First step: Setting upward the router

Find the guide bushing that attaches to the router base plate on the router inlay set.

Spiral the bushing to the router using the retaining ring, and so printing the sleeve onto the bushing to get ready to route the pocket.

After that, y'all set the depth of the cutting. You can set your router on a couple of blocks to leave yourself some space for the bit and plunge down to allow the scrap to protrude far enough to cut all the way through the inlay material.

Make sure to have set the depth end when you're done.

If y'all oasis't bought your bushing yet, you lot tin can buy yours from here

Second step: Routing the pocket

For smaller parts, you lot can apply double-sided tape to attach a template to your stock and to go along the stock in place as you road, secure information technology to the workbench.

You can even clamp information technology down if the workpiece is large plenty.

Once the template is attached and the work secured to the bench, you're ready to kickoff routing.

Set up the router on the template, then turn it on and plunge into the stock.

Try making shallow passes beginning and and then plunge in the full-depth cuts once y'all rest bodacious that you will get the best results.

Moreover, earlier you showtime working with the material in the middle, road effectually the edges of the pocket.

After you're done with routing the pocket, have a look at your work for any places that you might have missed with the router bit and clean them upward with a sharp chisel.

Then, remove the template using a putty pocketknife. This has been well demonstrated in this video, bank check it out!

Third step: Routing the Inlay

Before y'all start routing the inlay, remove the sleeve from the guide bushing.

No other changes to the router demand to be done.

Attach the template to your inlay stock with double-sided tape.

Clamping or taping some kind of backer board textile underneath would be great for cutting all the way through the inlay material.

Secure the workpiece to the backer board with a double-sided tabular array. Furthermore, under the area where the inlay will exist, put some tape to guarantee that it stays in place.

Proceed the guide bushing pressed firmly into the edges of the template all the time every bit you lot road the inlay.

In this where the plunge-base router is superior to the fixed-base router.

This is because, with a plunge-base router, it's a lot easier to go on the bushing pressed against the edge of the template when y'all begin cutting.

Similar routing the pocket, starting time with shallow passes then proceed to full-depth cuts.

Remove the stock and inlay with a putty knife, but be careful not to harm the inlay as you practise so.

Lightly sand the back edges and round the corners to match the outline of the pocket.

Try to encounter if your workpiece fits well. If it doesn't, spend some more than time on the corners.

Fourth step: Assembling the Inlay

If your inlay fits well, start applying glue to the pocket and utilize a brush to glaze the edges.

Put the inlay in the pocket and employ a hammer or a mallet with a scrap block to tap information technology in the desired position.

Place a canvass of wax newspaper on top of the inlay and clamp a flake block over the elevation of the work. Later on the gum dries, remove the clamps.

Finally, sand the inlay flush and you lot're done.

Just make certain that yous don't have any small gaps. If so, you tin can make full them with a solvent-based putty before you end. You lot can besides use a soft wax-based putty later on that.

Source: https://www.powersawexpert.com/how-to-inlay-wood-with-a-router/

Posted by: ochoapervage.blogspot.com

Share this post