How To Repair Iphone 6s Charger Port

Introduction

Use this guide to supervene upon the Lightning connector associates, which also includes the headphone jack and microphone.

Y'all can as well use this guide for reference when replacing the following parts:

• Battery Connector Subclass
• Front Panel Assembly Cable Subclass
• Lightning Connector Bracket
• Microphone Brace

• Before disassembling your iPhone, discharge the battery beneath 25%. A charged lithium-ion battery can catch burn down and/or explode if accidentally punctured.

• Power off your iPhone earlier beginning disassembly.

• Remove the two iii.six mm-long P2 Pentalobe screws next to the Lightning connector.



• The side by side three steps demonstrate using the iSclack, a slap-up tool for safely opening the iPhone vi that we recommend for anyone doing more than one repair. If you aren't using the iSclack, skip down three steps for an alternate method.

• If the plastic depth approximate is attached at the center of the iSclack, remove information technology now—it'south not needed for larger phones similar the iPhone half-dozen.

• Close the handle on the iSclack, opening the suction-cup jaws.

• Identify the bottom of your iPhone in between the suction cups.

• Position the iSclack'south upper suction cup against the display, only above (but not covering) the home button.

• Open the handles to shut the jaws of the iSclack. Center the suction cups and press them firmly onto the top and bottom of the iPhone.

• If your display or back drinking glass is badly cracked, covering it with a layer of clear packing tape may assistance the suction cups adhere. The iSclack besides includes two pieces of tape for this purpose.

• Hold onto your iPhone securely and close the handle of the iSclack to separate the suction cups, pulling the front end console up from the rear case.

• The iSclack is designed to safely open your iPhone just enough to separate the pieces, simply not enough to damage the display cables.

• Peel the 2 suction cups off your iPhone.

• Skip the next three steps and continue on to Step 8.

• If you don't have an iSclack, use a single suction loving cup to lift the front end console:

• Press a suction loving cup onto the screen, just to a higher place the home push.

• Be sure the cup is pressed deeply onto the screen to get a tight seal.

• If your display is badly cracked, covering information technology with a layer of clear packing record may allow the suction cup to attach. Alternatively, very strong tape may be used instead of the suction cup. If all else fails, you can superglue the suction cup to the broken screen.

• While holding the iPhone down with one hand, pull up on the suction cup to slightly separate the front panel associates from the rear case.

• Take your time and apply house, abiding force. The display assembly is a much tighter fit than most devices.

• Using a plastic opening tool, begin to gently pry the rear case down, abroad from the display associates, while continuing to pull upward with the suction cup.

• There are several clips holding the front panel assembly to the rear case, and then you lot may need to utilise a combination of the suction cup and plastic opening tool to free the front panel assembly.

• Pull the plastic nub to release the vacuum seal on the suction loving cup.

• Remove the suction loving cup from the display assembly.

• Open the iPhone past swinging the home button cease of the forepart panel assembly away from the rear case, using the acme of the telephone as a hinge.

• Several clips along the tiptop edge of the front panel form a partial hinge.

• During reassembly, align the clips merely beneath the peak edge of the rear case. Then, slide the forepart panel upwards until its top edge is flush with that of the rear case.

• Open up the brandish to well-nigh a 90º angle, and lean it against something to keep it propped up while you're working on the phone.

• In a pinch, an unopened canned potable works well for this.

• Add together a prophylactic band to continue the display securely in place while you piece of work. This prevents undue strain on the display cables.

• Remove the following Phillips screws from the battery connector bracket:

• One 2.2 mm spiral

• One 3.2 mm spiral

• During your repair, go on rail of each spiral and make sure it goes back exactly where it came from to avoid damaging your phone.

• Remove the metal battery connector bracket from the iPhone.

• Use a plastic opening tool to gently pry the bombardment connector upwards from its socket on the logic board.

• Take care to just pry upward on the battery connector, and not the socket on the logic board. If you lot pry up on the logic board socket, you may suspension the connector entirely.

• Remove the following five Phillips screws securing the front panel associates cable bracket:

• Iii i.2 mm screws

• One 1.vii mm screw

• Ane 3.1 mm spiral

• Wrong placement of these screws during reassembly will cause permanent harm to your iPhone's logic board.

• Remove the front panel associates cable subclass from the logic board.

• In the next iv steps, have care to pry up merely on the cablevision connectors, and not on their sockets on the logic board.

• Employ a spudger or a fingernail to disconnect the front-facing camera and sensor cablevision connector.

• Utilise a spudger or a fingernail to disconnect the dwelling button cable connector.

• Make sure the battery is disconnected earlier you disconnect or reconnect the cable in this step.

• Use a spudger or a fingernail to disconnect the brandish data cable connector.

• When reassembling your telephone, the display data cable may popular off its connector. This can event in white lines or a bare screen when powering your phone back on. If that happens, merely reconnect the cable and power cycle your telephone. The best way to power cycle your phone is to disconnect and reconnect the battery connector.

• Employ the apartment finish of a spudger to disconnect the digitizer cablevision connector.

• When reconnecting the digitizer cable, practise not press the center of the connector. Press one end of the connector, then press the contrary terminate. Pressing in the centre of the connector can curve the component and cause digitizer damage.

• Remove the front panel associates from the rear instance.

• Use the flat end of a spudger to disconnect the Lightning connector assembly cablevision and fold information technology out of the way of the speaker.

• Use the point of a spudger to lift the antenna cable connector up off of its socket on the logic board.

• Remove the following four Phillips screws securing the speaker:

• Two 2.9 mm screws

• Two ii.three mm screws

• Use the point of a spudger to push the antenna interconnect cable clip off of the speaker housing.

• Use the tip of a spudger to pry the speaker up and out of the rear example.

• Remove the speaker from the iPhone.

• Remove the two 1.6 mm Phillips #00 screws securing the vibrator to the rear case.

• Remove the vibrator from the iPhone.

• Remove the two 3.one mm Phillips #00 screws securing the Lightning port retaining bracket.

• Remove the Lightning port retaining bracket.

• Remove the single 3.half-dozen mm Phillips #00 shoulder screw from the microphone brace.

• Remove the microphone brace from the iPhone.

• Remove the six remaining Phillips #00 screws from the Lightning connector assembly:

• Ii 3.1 mm shoulder screws

• Ii ane.7 mm screws

• Two 1.5 mm screws

• Utilize the apartment end of a spudger to begin peeling the Lightning connector assembly upward from the rear case.

• Carefully pull the Lightning connector assembly up slightly to free it from the vibrator and speaker screw posts.

• Use the flat end of a spudger to elevator under the Lightning connector portion of the associates to free more than adhesive.

• Utilize the point of a spudger to push the microphone portion of the Lightning connector assembly out of its recess in the rear case.

• Gently run the point of a spudger under the associates between the Lightning connector and the headphone jack to free it from the last of the adhesive.

• Utilise the tip of a spudger to help guide the headphone jack out of its recess in the rear case.

• Remove the Lightning connector assembly from the iPhone.

• Before installing or replacing the Lightning connector associates:

• Use a plastic tool to scour any bits of agglutinative rest from the rear case backside the cable.

• Carefully compare your replacement office to your original cablevision and brand sure they match. Your replacement Lightning connector assembly may be missing certain components that demand to exist transferred from the original.

• Components that ordinarily need to be transferred include the headphone jack gasket, microphone bracket, and antenna interconnect clip.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Fastened Documents

Team

Embed this guide

Choose a size and copy the code below to embed this guide every bit a modest widget on your site / forum.

Preview

Source: https://www.ifixit.com/Guide/iPhone+6+Lightning+Connector+Assembly+Replacement/29915

Posted by: ochoapervage.blogspot.com

Share this post